Curious Inventor Blog

Just another WordPress site

VoS / Stribe demos at Dorkbot

Travis and I will be demoing some toys at the next Atlanta Dorkbot, which will be held at WonderRoot (directions). Travis is bringing the Voice of Saturn line and I’ll have some stribes and an arduinome. Also, Beth Milliken will talk about Freeside, a new Atlanta based non-profit Hackerspace – encouraging collaboration and innovation across hardware and software disciplines.

Arduinome Case Now Available / Build Log

Both black and clear acrylic arduinome cases can now be ordered. Our first batch is very limited, but more will arrive soon. This post will detail the building and programming process.

Building an Arduinome

This guide largely echos bricktable’s (thanks!), with some added bits and pieces.

Parts list:

Both our black and clear acrylic cases come with the following:

  • (16) 8-32 screws
  • (16) 8-32 nuts
  • (4) rubber feed
  • (2) 4-40 standoffs
  • (1) 2-56 screw (for small arduino mounting hole)
  • (5) 2-56 nuts (for small arduino standoff and nut)
  • (20) 4-40 .5″ screws for buttons
  • (20) #4 lock washers
  • (22) 4-40 nuts (for standoffs and button screws)

You’ll also need:

  • arduino Diecimila (or newer versions that accept shields)
  • unsped shield
  • spark fun buttons and pcbs
  • (64) bright LEDs (1000mcd blue LEDs shown) mouser: 604-WP7104PBC/A Both 3mm and 5mm LEDs with .1″ lead spacing fit. Standard LEDs will barely show through the buttons, even in low light.
  • (64) small-signal diodes
  • 8-Bit Shift Register. mouser: 512-MM74HC164N
  • 8-Bit PISO Shift Reg, mouser: 511-M74HC165
  • 10uF cap
  • (3) .1uF caps
  • 10 Pin Common Bus Resistor Network, mouser: 266-100K-RC
  • (2) 2×8 headers
  • (2) 16 pin IDC sockets
  • ribbon cable
  • (1)single row male headers
  • 24 pos. socket, 14 pos. socket, 16 pos. socket
  • MAX7721 or MAX7719
  • current limiting resistor, see the forward voltage chart here

Starting with software so we can test everything before installing all the screws.

Software: Setting the USB Serial ID, Firmware, ArduinoSerial, Monome Software

Outline: A program called ArduinomeSerial lets monome apps talk to the arduinome. In order for AruinomeSerial to recognize the arduinome, your arduino needs to have a new serial ID programmed into the FTDI USB-to-serial chip, as well as arduinome serial firmware.
Setting the USB Serial ID on the arduino:

  • Plug in the arduino
  • Download MProg and run it (PC only, any Mac solutions?).
  • Tools –> Read and Parse
  • In the “USB Serial Number Control” box, check “Use Fixed Serial Number” and type in a number like “a40h-001” or any variation on “a40h-xxx”. a40h- is the important part.
  • File–> Save As… whatever you like.
  • Device Menu –> Program
  • It should respond with a “programmed device with…” message.
  • The monome forums have more info on this process.

Load the arduinome firmware:

  • Download the arduinome firmware. Note: it may look like only the firmware is available, but if you click “arduinome” under package in the download page, you’ll find the ArduinomeSerial program.Download ArduinomeSerial, too.
  • Use arduino v11 to program the firmware.
  • Run ArduinomeSerial. If it lists your serial number under the “Device Settings” box, it found the device.

Hardware: Wiring the button pcbs, Soldering the Unsped PCB, Building the Case.

Install diodes: Make sure the line on the diode matches the silk screen. Trim their leads close (flush cutters!) so they don’t interfere with the buttons.

Install LEDs: Ground (shorter lead) is the 2nd hole from the flat side. The 3rd hole connects to the “Blue LED” line.


Wiring the pcbs: Feel free to do this how you like, but we cut 5″ & 10″ segments of ribbon cable, stripped both ends of the short segments and twisted them together with the stripped ends of the longer segments. Follow the wiring diagram below, and for a more complete schematic, check outcbit’s. It’s not a bad idea to beep-test (check connection) a few lines between the button pcb and the actual sockets on the unsped pcb.

Note: each blue & switch pair is flipped.

Click image for a larger version.
Solder Components to the unsped pcb:

Note: see here for info on choosing the current limiting resistor. We used a 15k to limit current to 30mA per LED, which was chosen based on the 3.2 forward voltage drop of our LEDs.


Clip the the 10th pin of the resistor package–only the first 9 are needed. The package is notsymmetrical, don’t clip pin 1.
Note: we broke off the break-out board because we’re not using it in these instructions.
Start building the case by attaching arduino to base:

First add the #2 screw and 4 #2 nuts to act as a standoff.

Now attach the standoffs with nuts to the arduino, and then use the shorter 4-40 screws (3/8″) to secure the 4-40 standoffs to the acrylic base plate.
Put buttons in top face:

Lay the button pcbs on the buttons, secure each with one screw in the middle.
Although not pictured, install the 4-40 lock washers under each nut.

Wiggle to make sure they’re seated correctly.
Before completing the case, download the monome_base apps and run monome_test:
Plug in the shield, IDC sockets, and USB cable. See the getting started instructions for a first test. If everything works, proceed ahead.
Continue installing the rest of the 20 button screws, washers and nuts.
Begin installing side panels:
Slide a nut into its slot, and then insert the screw through its corresponding hole.
Finish two sides, and then begin installing the top.

The picture shows all 4 sides installed first, but by doing only two sides first it’s easier to grab nuts that may fall inside. Also, the sides of the acrylic have a slight angle, so they’ll tilt a small amount if only the top or bottom is attached. Counter this by holding the side in place while securing the top.

When everything is in place, tighten down all screws.

Bleepnome: bleepified monome 40h


“… the bleepnome has 2 photocell tenticles and 2 led tenticles. So it reacts to light on the monome to change either pitch or modulation. The multiscreen aspect of SevenUpLive lets me control the 40h lights from the 128…. ” video goodness ( by barnone )

Sudoku, Diesel-Engine Hammond Organ, Fly-Wheel, Stretched Skin Instruments

The Guthman New Musical Instrument Competition was this weekend, and brought in some very inventive new music-making devices from around the world. Here’s a small sample (more pics to come): SoriSu (video) (Hyeki Min): a Sudoku game that algorithmically generates music based on your play, using the same rules as Sudoku. Wrong plays generate harsh dissonance as punishment.Hammond Organ from Engine (jan perschy, austria): Old Hammond organs generated sound not from electronic oscillators, but tonewheels–actual spinning wheels with magnets sensed by pickups. Rich timbres were made by mixing these tones together (“additive synthesis”). Jan has replicated this idea but uses various rotating parts in an engine for tone wheels. The pickups are actually Harley Davidson pickups used to detect piston position in actual motorcycles. The keys gate the pickups on/off. Motors on Fly-Wheels Sensed by Guitar Pickups (Neil Feather): Some of the best music (in the author’s opinion) came from one of the simplest instruments. Three fly wheels, each with a couple electric motors mounted on them. Neighboring guitar pickups hear different tones depending on how fast the the wheels are spinning, and lots of interesting phasing / beating effects were generated that slowly changed as the wheels slowed down. The inspiration apparently came from swinging vibrators near guitars… Silent Drum (Jaime Olilver): The 2D profile made by pressing and stretching a drum skin is used to control a phase vocoder. This was the winner of the competition. This instrument had a great connection between what you heard and what you saw.

Light sensitive transistors pick up the varying refresh rates on cell phone displays. The artist (Robert Mathy) plays by pointing his fingers at various positions on the displays. Blinking lights make interesting rhythmic patterns.


Skot Wiedmann brought an insane death-star patch-bay, which even he couldn’t explain how it really worked. Somewhat neural-nety, he said he was interested in the results of combining random collections of circuits.

David Wessel (Berkeley’s CNMAT) brought the ultimate touch pad array, feeding his computer 96 channels of audio signals over ethernet that contained x,y and force for each pad.

Dorkbot Atlanta – 02.25.09 – The Buchla Synthesizer and Classic Amiga Hardware

Review of this month’s Atlanta Dorkbot meeting featuring Don Hassler’s Buchla 200e demo, and Aaron Ruscetta’s old school Amiga hardware presentation.

“… Buchla, along with Robert Moog are credited for being the fathers of the synthesizer, both sort of simultaneously developing synthesizers on either coast. Buchla was involved with the San Francisco Tape Music Center, founded by the composers Morton Subotnick and Ramon Sender. The tape music center was a place for new music performances, experimentation, and several psychedelic parties which, at the height of the Haight-Ashbury scene, included bands that went on to huge success like the Grateful Dead…. ” ”
This month’s Atlanta Dorkbot was held in its new home, Wonderroot, a non-profit community center of sorts that has meeting space, rock shows, an art gallery, and even recording facilities.

https://youtube.com/watch?v=mO6XsA6d4hE

The first presenter was Don Hassler, a local Atlanta musician/artist (bio here) who has been working with electronics for music since the early 80’s. Don (shown in video), did a nice demonstration of some of the basic features of his Buchla 200e modular synthesizer. The 200e is an updated series from Don Buchla’s original, and incredibly unique analog modular systems of the 70’s. Buchla, along with Robert Moog are credited for being the fathers of the synthesizer, both sort of simultaneously developing synthesizers on either coast. Buchla was involved with the San Francisco Tape Music Center, founded by the composers Morton Subotnick and Ramon Sender. The tape music center was a place for new music performances, experimentation, and several psychedelic parties which, at the height of the Haight-Ashbury scene, included bands that went on to huge success like the Grateful Dead.
Buchla’s synthesizers were unique in that they weren’t necessarily design to be played with traditional keybaords, rather they were meant to be completely new instruments, with inspiring interfaces. Don’s demo of his modular was simple, yet pointed out the components and design philosophy that differentiated the Buchla instruments from other synthesizer, both vintage and new.
You can find more information as well as some of Don Hassler’s music on his website
The second presenter was Aaron Ruscetta, a media artist, and editor, and Amiga enthusiast who enthusiastically gave a great overview of the history of the Amiga computer, and the culture of users that it created.


Aaron went through the histor of the Amiga computer, and talked about his experience as a video editor and graphic artist with the Amiga systems. Starting with the earliest home computers such as the Commodore 64, the Demoscene exploded with advent of the Amiga’s unprecedented graphics power. Demos were basically programs written to show off graphics processing capabilities of systems, but many of the early demo creators reached a sort of cult status amongst graphic programmers. Also interesting to note, the demo scene was also somewhat responsible for the birth of music trackers. Artists wanted to add music to their demos, and so created simple table-based sequencers for stringing together samples to create music. the demo/tracker scene in turn had a big hand in spawning IDM, glitch, etc. music genres. Aaron is now the First Contact and Event Coordinator for the Atlanta Linus Enthusiasts User Group

New Plug-In Bread Board Adaptors

Designed in cooperation with uCHobby, these bread board adapters make it easy to plug in audio plugs, multimeter probes, bare stranded wires that are too big for the bread board holes, MIDI I/O. Also released is a dual power supply that should help out in op-amp audio projects, and a proto area you can solder common circuits onto so they can be quickly plugged into new projects. All the boards are designed to take up as little work-space as possible, and either stand up or hang off the edge.

Controlling 4 or More Servos Demo Arduino Code

The newest version of arduino has a SoftwareServo library built in, which lets you use more than two servos at once. This code is a simple example of how to control 4 servos via keyboard from the SerialMonitor mode of arduino. If you have arduino12 software, you’ll need to manually add the SoftwareServo library as described in the included readme.txt file. The code is available as a getting started example on our roboduino kit page.

Hand Wiring No-Lead Chips

Robert Dew did some amazing tack-soldering on the bottom of a No-Lead chip to make a simple break-out board without any special PCBs. He says it took a lot of trial and error and flux. The chip is an accelerometer. Robert made the break-out board for the EE senior design class and electronics lab at GaTech.

About

CuriousInventor launched in late 2006 (pre-arduino era!) as a place to enable hobbyists, students, and musicians to create their own technology. We sold open-source kits and tools, and offered numerous guides & videos on things like soldering, metal working, screws, electronics, and more. 

The store is now mostly empty, but we’ve kept the product pages and guides up since they have useful information. Many of our guides and videos still rank on the first page of google searches and have been seen millions of times. Content on this site and the CuriousInventor YouTube channel produced by Scott Driscoll.

Top Videos